FABRICATOR II

Anderson DahlenDescription : Gray's Specialty Equipment segment offers a comprehensive range of expert services to design, manufacture, integrate, install, and maintain some of the most advanced systems on the market. The Specialty Equipment segment includes Anderson Dahlen, located in Ramsey, MN, and Waconia, MN. Anderson Dahlen delivers end-to-end equipment design-build and contract manufacturing, with precision fabrication - cutting, forming, machining, welding, finishing, and complex assemblies - backed by engineering, integration, and complete process solutions including skids and sanitary platforms tailored to customer applications. Anderson Dahlen is ISO 9001 : 2015 certified, as well as ASME, AWS, and PED compliant. The wage range for this role takes into account a wide range of factors that are considered in making compensation decisions including but not limited to skill sets; experience and training; certifications; as well as other business and organizational needs. The disclosed range estimate has not been adjusted for the applicable geographic differential associated with the location at which the position may be filled. It is not typical for an individual to be hired at or near the top of the range for their role and compensation decisions are dependent on the facts and circumstances of each case. A reasonable estimate of the current range is $24 to $33 hourly. PRIMARY OBJECTIVE OF THE POSITION : Operates press brakes and rolls to form a variety of sheet metal components within customers tolerances and company quality standards.MAJOR AREAS OF ACCOUNTABILITY : Provides optimum cooperation and complete information to Supervisor and other personnel, relative to projects within his / her assigned team, to ensure on-time and accurate job completion.Works from drawings, sketches, routing notes, and instructions to determine operational requirements and makes arithmetic calculations to develop formed lasered / water jet / sawed / sheared sheet metal parts.Uses calculator to perform math calculations for forming operations.Works on small to large parts where the tolerance and accuracy are normally difficult and hard to maintain.Uses proper dies and automated back gauge to accomplish assigned tasks on Cincinnati press breaks.Ability to run / learn how to roll various sized straight walls and cones on various rolling machines.Ability to run the shear, band saws, drills, and various hand tools.Runs overhead crane and forklift to retrieve material. Uses tape, caliper, square and protractor to determine product conformity to requirements.Checks work as necessary to assure holding prescribed tolerances to maintain quality standards.Detects defective materials, unusual conditions or operating difficulties for reporting and relays information to supervisors.Applies Lean Manufacturing efforts to reduce setup time, increase Fabrication throughput, and improve flexibility and response of the manufacturing system.Other duties as assigned. Requirements : QUALIFICATIONS FOR ENTRY : High school education or equivalent.A minimum of 2-3 years of fabrication and press brake operator experience.Ability to demonstrate good working knowledge of shop math applications.Demonstrated ability to handle and lift varying weights up to 50 lbs. consecutively.Ability to read and interpret complex drawings, routings, and instructions.Ability to use a variety of hand tools, measuring instruments, and operation of all related sheet metal and fabricating equipment. Maintains and determines efficient methods, organization of work, selection of proper machine, and takes care to maintain finish.PHYSICAL REQUIREMENTS : The company fosters a manufacturing-type environment. The physical demands described below are representative of those that must be met by a team member to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. Lift / Carry 0-10 lbs. continuously.11-50 lbs. frequently51-100 lbs. neverPush / Pull-0-25 lbs. continuously26-100 lbs. frequentlyBend- 34-66% during a 10 / 12-hour shiftTwist / Turn- 34-66% during a 10 / 12-hour shiftKneel / Squat- 0-33% during a 10 / 12-hour shiftSit- 0-33% during a 10 / 12-hour shift.Stand / Walk- 67-100% during a 10 / 12-hour shiftOverhead Reaching- 0-33% during a 10 / 12-hour shift Ladder / Stair- 0-33% during a 10 / 12-hour shiftEEO DISCLAIMER : Gray is proud to be an Equal Opportunity Employer and welcomes everyone to apply. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, gender identity, sexual orientation, national origin, or protected veteran status and will not be discriminated against on the basis of disability.All qualified applicants will receive consideration for employment without regard to race, color, sex, sexual orientation, gender identity, religion, national origin, disability, veteran status, age, marital status, pregnancy, genetic information, or other legally protected status.Compensation details : 24-33 Hourly WagePIeff567ac3cb3-25660-38987167